Biogas methane content is a relevant variable in anaerobic
digestion processing where knowledge of process kinetics or an early indicator
of digester failure is needed. The contribution of this work is the development
of a novel, simple and low cost automatic carbon dioxide-methane gas sensor
based on the solubility of gases in water as the precursor of a sensor for
biogas quality monitoring. The device described in this work was used for
determining the composition of binary mixtures, such as carbon dioxide-methane,
in the range of 0–100%. The design and implementation of a digital signal
processor and control system into a low-cost Field Programmable Gate Array
(FPGA) platform has permitted the successful application of data acquisition,
data distribution and digital data processing, making the construction of a
standalone carbon dioxide-methane gas sensor possible.
Low-cost
chemical analysis sensors can have a great impact in fields such as
environmental preservation and energy efficiency. There is a growing market for
this kind of sensor, especially for low-cost and reliable sensors focused on
carbon dioxide (CO2)-methane (CH4) mixtures in biogas
quality monitoring applications. Currently, the most studied method to
transform waste into energy is anaerobic digestion, which can convert a variety
of wastes, such as agricultural waste from animals and plants and municipal
waste, into a full energy product such as biogas. The preferred technology for
the analysis of single components in raw biogas, specifically to determine the
CH4 and CO2 content, is optical sensors, which detect
infrared absorption in the characteristic wavelengths for these molecules. In
the literature, biogas composition has been measured with gas infrared
analyzers, such as those used by Sedlačík and Dvořáčková,
who utilized a GASCARD II infrared gas sensor from Edinburgh Instruments;
Nordberg et al., who used a
Model 6500 visible/near-infrared scanning monochromator from FOSS NIRSystems
and Steyer et al. , who used a
Siemens Ultramat 22P, which works on the principle of the nondispersive
absorption of infrared light. Additionally, semiconductor diode lasers for use
in the mid-infrared spectral region based upon lead-salt operating near 7.8 μm
have also been used for methane measurements. However, there are two main
drawbacks to the sensors outlined above: high cost and difficulty of
installation at all biogas production sites. For comparison, the cost of a
commercial FTIR spectrophotometer is near $20,000 USD, while the estimated cost
of the gas sensor described here is approximately $5,000 USD. The described
sensor is also easy to build and operate.
Methods for the
acquisition of biogas methane content based in a variety of measurement
principles have been reported in the literature. For example, Mandal et al. determined biogas quality using
flame temperature as the measurement principle. In this case, the steady-state
flame temperature was measured using a system consisting of a thermocouple
probe and an analog temperature indicator. In addition, Rego and Mendes and Rego et
al. described a permselective gas sensor for determining the
composition of carbon dioxide-methane mixtures in the 0–100% range. The sensor
consisted of a permselective membrane, a pressure transducer for measuring the
permeate pressure and a needle valve for controlling the permeate outlet to the
atmosphere. Furthermore, Rozzi et al.
used a thermostatically controlled cell containing 0.1 mol · L−1
sodium bicarbonate in which the pH was monitored by an Orion combination glass electrode
and an Orion Model 601A specific ion meter. When the pH reading had stabilized,
gas samples were taken using a syringe and analyzed for CO2 and CH4
content using gas-solid chromatography on molecular sieves with nitrogen as the
carrier gas and a katharometer for the detector.Carlson and Martisson presented a technique to quantify variations in ultrasound pulse shape caused by interactions between the constituents of a two-component gas mixture as an alternative method to extract information concerning the molar fraction of a gas in a binary mixture. Additionally, Tardy et al. developed a dynamic thermal conductivity sensor for gas detection based on the transient thermal response of a SiC micro-plate slightly heated by a screen-printed Pt resistance. This device was intended for specific application in the determination of the specific gases in a mixture.
Gonzalez et al. used a device that passed the produced biogas through an Erlenmeyer flask filled with a 20% NaOH solution followed by a tube filled with soda lime pellets. The gas then passed through a Mariotte flask system containing water for the quantification of methane production. The displaced water was collected in a plastic container on a pressure sensor (QB 745, DS-Europe) for continuous monitoring of CH4 production.
A Field Programmable Gate Array (FPGA) is an array of basic logic blocks where the user can define its interconnectivity, making it programmable in a fully open architecture. Therefore, an FPGA provides the advantages of a general-purpose processor and a specialized circuit that can be reconfigured as many times as necessary until the required functionality is achieved. The speed and size of the FPGA are comparable with the Application Specific Integrated Circuit (ASIC), but the FPGA is more versatile and its design cycle is shorter because of its reconfigurability. FPGA applications go beyond the simple implementation of digital logic; they can be used for the implementation of specific architectures for speeding up some algorithms. A specific structure for an algorithm implemented into an FPGA could have 10–100 times higher performance than its implementation on a Digital Signal Processor (DSP) or microprocessor.
Due to the sequential processing data flow on commercially available DSPs and microprocessors, the increase in sampling rate, mathematical processing, or versatility can impose severe restrictions on processor performance. Therefore, other alternatives for signal processing must be considered to achieve real-time data acquisition and data pre-processing. Moreover, FPGA devices have been gaining market share in system on chip (SOC) applications because they can integrate processing units defined by the user and related peripheral logic in the hardware, combining open architectures that do not depend on the manufacturer or specific platforms. However, DSPs and microprocessors have a fixed sequential construction for computation, which can easily be overloaded when the processing time between samples is significantly reduced, as in high-speed control, while FPGAs have a natural parallel architecture for high-speed computation. Along with the advantages previously cited, FPGA development is performed under Hardware Description Language (HDL), making the design portable and platform independent, which is not the case for commercially available DSPs or microprocessors.
In
this paper, the development of a low-cost automatic carbon dioxide-methane gas
sensor based on the principle of the solubility of gaseous species in water is
reported. The novelty of this work is two-fold. First, a physical principle,
never used before, is applied for binary mixture quantification, drastically
reducing the cost and complexity of the equipment and facilitating on-line
monitoring. Second, the hardware implemented in the FPGA has the capacity for
data acquisition, data distribution, data processing, data communication and
control, adding functionality and autonomy to the automatic carbon
dioxide-methane gas sensor and allowing it to be deployed in the field.
没有评论:
发表评论